Aluminium is a component, not a category

On a suitcase, aluminium turns up in four distinct places, and a case can use any combination of them: the frame around the case mouth, the corners and closure hardware, the telescopic handle tubes, and - rarely - the body itself. Which of the four a quotation actually includes is the difference between comparing like with like and comparing two different products.

That is why "aluminium luggage" means very different things at very different price points. It is a material choice, not a single product category.

What an aluminium frame case actually is

An aluminium frame case is not a solid aluminium body. It is a polycarbonate or ABS+PC shell joined to an extruded aluminium profile frame that runs around the opening. The aluminium carries the load at the case mouth - the point where a zippered case fails first - while the shell provides the body. The frame is bent from profile and riveted closed, not welded.

If a supplier describes a case as entirely aluminium while quoting a polycarbonate shell, the specification is inconsistent. Resolve it before you pay for a sample.

Frame hardness: the number to ask for

The aluminium case mouth is tested for Brinell hardness under ISO 6506 / ASTM E10 and must reach at least 40 HWB. That figure is a core structural benchmark in our mechanical luggage testing protocol, not an optional extra. A frame below it deforms at the opening long before the shell fails, which is why a frame quotation without a hardness figure is incomplete.

How the frame is made

The profile is extruded from 5052 or 6061 aluminium alloy to the required cross-section, cut to the case perimeter, bent to the corner radii and riveted to the Covestro PC or ABS+PC shell (or to a 5052/6061 stamped metal body on our full-aluminium suitcases). The corners and the closure come from the same aluminium-magnesium alloy family as the profile. Anodising is the standard finish, with the oxide film specified at 10-12 micrometres, paired with SilentMove 360° spinner wheels.

Extrusion and anodising being outsourced is normal in this industry and not a weakness in itself. What matters is that mould making, bending, riveting and frame alignment stay inside the plant, because alignment is what the case mouth hardness ultimately depends on.

Testing that applies to aluminium frame cases

Structural testing follows our in-house and SGS physical luggage durability protocol. The aluminium-specific requirements are case mouth hardness (ISO 6506 / ASTM E10) and 16-hour neutral salt spray testing (ISO 9227 / ASTM B117), because an anodised frame is exposed to the same handling as the shell. Drop, low-temperature drop, SilentMove wheel and stacking testing apply to the completed case regardless of shell material.

One point many quotations get wrong: the roller-drum impact and falling-ball tests written for plastic shells are explicitly not applicable to metal-bodied cases. An aluminium case has to be tested against the aluminium requirements, not borrowed from the plastic test list.

Finished cases are sent to SGS for testing, which produces test reports on submitted samples rather than a product certification.

Aluminium or polycarbonate: how to decide

Most ranges carry both. A brand will put an aluminium frame line or full aluminium line at the top of the range and Covestro polycarbonate or PP below it, because the frame signals the higher price point while the plastic shells carry the volume. The aluminium frame costs more, weighs more and reads as premium; polycarbonate is lighter and absorbs impact instead of transferring it.

Neither is better in the abstract. The question is which position in your range you are filling.

Ordering aluminium luggage

See the aluminium frame range in the catalogue, or compare all five hard-shell routes in material choices for hard shell luggage. Read how an OEM or ODM programme is structured.

Alloy Grade and Sheet Thickness: Defining 5052 vs 6061 in Luggage Specifications

PT. DJI Travel Products Indonesia manufactures both full-aluminium luggage and composite cases using aluminium alloys 5052 and 6061. In hard-shell luggage manufacturing, these two grades fulfill distinct mechanical roles based on formability and tensile strength. Alloy 5052 contains magnesium as its primary alloying element, providing high elongation and cold workability. This ductility makes 5052 the practical standard for deep-drawn ribbed panels, contoured shells, and stamped corner protectors, as the metal deforms into complex dies without tearing. Alloy 6061 includes both magnesium and silicon and is heat-treatable to higher yield strengths. It is less suited to deep stamping but performs effectively as extruded structural framing, where structural rigidity and resistance to perimeter racking under latch tension are critical.

A bill of materials or product sheet that specifies only "aluminium" provides insufficient data for commercial sourcing. Unspecified metal listings often mask lower-grade scrap alloys or soft tempers that lack dent resistance and develop surface pitting during finishing. Furthermore, because weight is a primary metric in export luggage, an ambiguous entry obscures whether structural integrity comes from proper metallurgical temper or simply excess dead weight. Clear alloy callouts ensure that your finished shells hold tight dimensional tolerances across temperature shifts, while keeping closure channels square over repeated cycles.

Rather than accepting generic terminology, importers and brand owners should require three precise measurements in their technical specifications:

Sheet gauge and alloy requirements directly affect blank sizing, draw depth, and tonnage requirements during stamping. Because we execute tooling 100% in-house at our Bogor plant, our engineering team sets these parameters during technical drawing sign-off. Final component weights and wall thicknesses depend on your project requirements, target case volume, and whether the shell construction is full aluminium or an aluminium frame paired with a polycarbonate panel.

Surface Finishing: Anodising, Paint, and Brushed Metal — What Wears First

When specifying metal components—whether for full-aluminium shells or structural 5052 and 6061 aluminium frames—surface durability is governed by the application method and coating thickness. We process frame anodising to a layer depth of 10–12 micrometres, achieving a surface hardness of ≥ 40 HWB measured according to ISO 6506 / ASTM E10. In contrast to surface-level paints, anodising converts the exterior metal into an integrated aluminium oxide layer. Buyers evaluating factory specifications should focus directly on this micron depth, as cosmetic finishes below 8 micrometres fail prematurely under automated conveyor belt friction.

Finish Type Transit Wear Profile (12 Months) Scratch Visibility Specification Requirement
Silver Anodised Resists point impacts; micro-abrasions smooth out over time Lowest; exposed base metal matches surface colour Specify 10–12 µm layer depth, hardness ≥ 40 HWB
Dark / Coloured Anodised Oxide layer intact, but sharp shear forces penetrate dye depth High; silver substrate shows through black or tinted dyes Specify sealed dye with 10–12 µm anodising baseline
Painted / Wet-Coated Chipping and peeling along corners, rivets, and mating lips Severe; paint flakes leave stepped edges of raw metal Requires secondary primer; not recommended for high-impact frames
Brushed / Mechanical Polish Susceptible to surface transfer marks, scuffs, and salt oxidation Moderate; lateral scuffs blend along longitudinal grain Must be paired with a protective anodised clear seal

In transit, painted metal finishes degrade first. Because wet paint forms a mechanical film over the metal rather than an integrated metallurgical bond, localized flex and corner impacts break adhesion, leading to visible chipping along extrusion edges. Anodised surfaces do not flake or peel; wear occurs strictly through surface abrasion. However, colour choice changes how that abrasion appears to the end consumer. Black, charcoal, or coloured anodised surfaces show bright silver substrate lines as soon as luggage handlers slide cases across rough surfaces, whereas natural silver anodising conceals standard airport abrasion because the wear scar matches the base alloy.

To establish clear quality standards for your brand, avoid vague purchase order terms such as "scratch-resistant finish" or "matte coating." Specify the precise anodic thickness of 10–12 micrometres, verify hardness parameters against ISO 6506 / ASTM E10, and select finish tones that reflect your product line's expected wear profile.

Aluminium luggage sets: configuring 20 / 24 / 28 without doubling freight

To reduce ocean shipping volume on international container runs from our Kemang, Bogor factory, hard-shell luggage is routinely shipped as nested sets. A standard three-piece configuration places the 20-inch carry-on inside the 24-inch suitcase, which is then packed inside the 28-inch piece. Because the exterior dimensions of our 28-inch frame define the overall carton footprint (49.5 x 32 x 68.5 cm for the case), nesting three units inside a single master carton consolidates total freight volume to that of the largest case, avoiding the tripled cubic metre charge of shipping three separate cartons.

Importers should configure sets based on line tooling, as sizing varies across our four manufacturing series. The AURA Collection (full aluminium shell) and Captain aluminium frame line (PC or ABS+PC shell) support 20, 24, 26, and 28-inch tooling. The Captain zipperless and Voyager lines support 20, 24, and 28-inch tooling; the 26-inch mould is not available for these two series. When building a set, buyers standardise shell materials—such as 100% Covestro PC or full 5052/6061 aluminium—across all sizes. Mixing shell substrates within one set alters wall flex, internal clearance tolerances required for smooth nesting, and anodising finish consistency across aluminium frames.

Set Configuration Compatible Product Lines Production Order Minimum (Per Colourway) Carton Packing Format
3-Piece Set (20 / 24 / 28) AURA, Captain aluminium frame, Captain zipperless, Voyager 100 sets (100 pcs of 20", 100 pcs of 24", 100 pcs of 28" = 300 pcs total) 3-in-1 nested (20" inside 24" inside 28")
2-Piece Set (20 / 24) AURA, Captain aluminium frame, Captain zipperless, Voyager 100 sets (100 pcs of 20", 100 pcs of 24" = 200 pcs total) 2-in-1 nested (20" inside 24")
2-Piece Set (20 / 26) AURA, Captain aluminium frame only 100 sets (100 pcs of 20", 100 pcs of 26" = 200 pcs total) 2-in-1 nested (20" inside 26")
2-Piece Set (24 / 28) AURA, Captain aluminium frame, Captain zipperless, Voyager 100 sets (100 pcs of 24", 100 pcs of 28" = 200 pcs total) 2-in-1 nested (24" inside 28")

Because factory minimum order quantities are calculated at 100 pieces per SKU (one size in one colour), ordering a nested three-piece set requires a base production run of 100 units per size, yielding 100 complete sets (300 cases total). Sampling takes 7 to 15 working days, followed by mass production in 25 to 55 days depending on batch size and shell finish. Completed orders ship EXW Bogor with export documentation including COO / SKA (such as Form E, Form D, or RCEP) and custom outer carton markings.

Aluminium vs Polycarbonate vs Carbon Fibre: Material Behaviour in Luggage Transit

Luggage shells face concentrated point impacts, dynamic drops, and heavy compressive loads in commercial baggage systems. Polycarbonate, such as the virgin Covestro PC used in our Voyager and Captain lines, absorbs transit shocks through elastic deformation, flexing under load and rebounding to its original geometry. Full aluminium cases, such as our AURA Collection using 5052 and 6061 alloys, absorb kinetic energy through plastic deformation, resulting in localised surface denting without puncturing the shell wall. In contrast, carbon fibre composite shells possess high rigidity but low ductility; under concentrated impact loads against steel conveyor corners, the resin matrix cannot flex, leading to delamination or brittle fractures.

Sub-zero conditions during ground handling and high-altitude transit alter material mechanics. In-house and SGS drop testing evaluates impact integrity by dropping cases from 900 mm onto solid steel plates at ambient room temperature (18 to 25 °C), as well as a 90 cm drop after four hours of continuous conditioning at -12 °C. Polycarbonate retains high ductility and shock absorption at -12 °C, preventing structural splits when reinforced with 5052/6061 aluminium frames anodised to 10–12 micrometres (hardness >= 40 HWB). Aluminium alloys experience no ductile-to-brittle transition at airport temperatures, maintaining structural resistance under low-temperature drops. Carbon fibre panels rely on binding resin systems that can turn brittle when subjected to -12 °C shock loading, increasing crack propagation risks.

For brand owners, shell selection dictates post-sale warranty management and operational tare weight. Aluminium shells that suffer deformation can often be mechanically pushed out, whereas cracked carbon fibre shells cannot be reshaped and require full unit replacement. In production weights, a registered 20-inch full-aluminium shell weighs 3.7 kg net, while PC shells paired with riveted aluminium frames weigh 4.04 kg (Captain aluminium frame), 4.38 kg (Voyager), or 4.85 kg (Captain zipperless). While carbon fibre is frequently marketed for premium novelty, its brittle impact mode and high replacement liability make virgin PC-aluminium hybrids and full aluminium far more predictable substrates for commercial distribution.

Metric Full Aluminium (AURA) Polycarbonate + Aluminium Frame Carbon Fibre Composite
Primary Impact Response Plastic deformation; dents under heavy impact without cracking Elastic deformation; flexes under shock and returns to shape Brittle response; risk of delamination or wall cracking under point load
Drop Test (-12 °C after 4 hrs, 90 cm) High structural integrity; alloy does not suffer cold embrittlement Maintains flexural strength; Covestro PC resists shell rupture Resin matrix stiffens; susceptible to hairline fractures upon steel impact
Field Repairability Dents can be reshaped manually; riveted corners are serviceable Frame can be serviced; shell resists puncture in normal transit Non-repairable; cracked composite panels require complete disposal
20-inch Net Weight Profile 3.7 kg (aluminium-suitcase line) 4.04 kg (Captain) to 4.38 kg (Voyager) Varies by weave; offers high stiffness but no ductility advantage
Commercial Utility for Importers High perceived retail value, long service life, predictable wear Balanced protection, impact recovery, accessible warranty servicing Niche marketing appeal, high scrap rates if dropped, rigid failure mode

Questions buyers ask about aluminium luggage

Which aluminium alloy grade do you use for frames and full-metal bodies? We use 5052 and 6061 aluminium alloys, anodised to a 10–12 micrometre oxide layer and tested to ISO 6506 / ASTM E10 Brinell hardness ≥ 40 HWB at the case mouth.

Are your aluminium frames welded or riveted? They are bent from extruded 5052/6061 profile and riveted closed rather than welded, which preserves the temper and hardness of the alloy at the corners and closure.

What is the MOQ for custom aluminium-frame or full-aluminium suitcases? MOQ is 100 units per SKU (per colour × size combination), with 7–15 working days for sampling and 25–55 days for bulk production.

View all